« previous next »
Pages: [1]   Go Down

Author Topic: Connecting rod bearing screw  (Read 3135 times)

xeon100

  • Newbie
  • *
  • Posts: 16
    • View Profile
    • Email
Connecting rod bearing screw
« on: October 16, 2014, 04:03:16 PM »
Any tips on removing the big flat head screw that connects the rod bearing to the crank? Is it left or right hand? I hate flat head screws - I couldn't get it to budge. I started tearing my engine down for a rebuild today. Its an M model. I've read through the forum to get an idea of what I am in for. Thanks for the help!
Logged

Ricks

  • Administrator
  • Hero Member
  • *****
  • Posts: 3633
  • 1953 Automatic
    • View Profile
    • Email
Re: Connecting rod bearing screw
« Reply #1 on: October 16, 2014, 04:17:41 PM »
Do you have a big screwdriver that fits the slot properly?  If not, get one.  If you do, and it will not budge, put some heat on it.  When I put my motors together, I put a drop of loc-tite on them to ensure they don't loosen up.  Maybe others do the same.  Heat will break the bond.  If that doesn't work, an impact driver would be my next step.
Logged
Rick

xeon100

  • Newbie
  • *
  • Posts: 16
    • View Profile
    • Email
Re: Connecting rod bearing screw
« Reply #2 on: October 16, 2014, 04:51:52 PM »
So standard tread? I didn't want to put an impact on it but will try again this weekend.
Logged

Ricks

  • Administrator
  • Hero Member
  • *****
  • Posts: 3633
  • 1953 Automatic
    • View Profile
    • Email
Re: Connecting rod bearing screw
« Reply #3 on: October 16, 2014, 05:39:09 PM »
If you have a small propane torch, I would try that before the impact driver.

I think it is standard threads, but can't remember.  Old age is setting in!  Lol
Logged
Rick

cotton

  • Newbie
  • *
  • Posts: 49
    • View Profile
    • Email
Re: Connecting rod bearing screw
« Reply #4 on: October 16, 2014, 07:36:13 PM »
yep right handed thread.
Logged

pd

  • Hero Member
  • *****
  • Posts: 3130
    • View Profile
Re: Connecting rod bearing screw
« Reply #5 on: October 17, 2014, 02:08:29 PM »
I wouldn't be afraid to use an impact driver . If the screw won't budge by hand pressure and heat , like Rick said , an impact is the best next step .
 That's exactly why they were invented . ;)

Pete . :)
Logged
Goes around , Comes around . :)

xeon100

  • Newbie
  • *
  • Posts: 16
    • View Profile
    • Email
Re: Connecting rod bearing screw
« Reply #6 on: October 23, 2014, 05:15:13 PM »
Got it done this weekend. I torched it. Didn't budge easy but it finally broke free. I also pulled the crank pulley. Thanks to this site I knew ahead of time that it was left hand thread!

Thanks
Logged

pd

  • Hero Member
  • *****
  • Posts: 3130
    • View Profile
Re: Connecting rod bearing screw
« Reply #7 on: October 23, 2014, 05:59:23 PM »
Good you got the screw out without too much trouble .

The direction for removal was stamped on the pulley on my motor .



Pete . :)

« Last Edit: February 07, 2018, 09:14:23 AM by pd »
Logged
Goes around , Comes around . :)

Ricks

  • Administrator
  • Hero Member
  • *****
  • Posts: 3633
  • 1953 Automatic
    • View Profile
    • Email
Re: Connecting rod bearing screw
« Reply #8 on: October 23, 2014, 07:03:25 PM »
Quote from: pd on October 23, 2014, 05:59:23 PM
Good you got the screw out without too much trouble .

The direction for removal was stamped on the pulley on my motor .



Pete . :)



Not always!  I have seen some with, some without.
Logged
Rick

pd

  • Hero Member
  • *****
  • Posts: 3130
    • View Profile
Re: Connecting rod bearing screw
« Reply #9 on: October 23, 2014, 07:41:57 PM »
Quote from: RickS on October 23, 2014, 07:03:25 PM
Quote from: pd on October 23, 2014, 05:59:23 PM
Good you got the screw out without too much trouble .

The direction for removal was stamped on the pulley on my motor .



Pete . :)



Not always!  I have seen some with, some without.

Maybe due to Monday mornings and Friday afternoons ??? LOL

Pete . :)
Logged
Goes around , Comes around . :)
Pages: [1]   Go Up
« previous next »