« previous next »
Pages: [1]   Go Down

Author Topic: Flywheel torque  (Read 2073 times)

ramwing7

  • Newbie
  • *
  • Posts: 27
    • View Profile
    • Email
Flywheel torque
« on: April 08, 2023, 07:23:31 AM »
Anybody know the flywheel nut torque spec?

Thanks.
Logged

pd

  • Hero Member
  • *****
  • Posts: 3130
    • View Profile
Re: Flywheel torque
« Reply #1 on: April 09, 2023, 06:28:14 AM »
I sure don't know the specific spec .
I always just make sure that nut is good and tight . Too loose and the flywheel can shear the woodruff key without much trouble . That , specially if the crankshaft taper and the flywheel tapers don't match well . It's why I recommend lapping the flywheel to the crankshaft . The better the tapers match , the better chance of the flywheel not spinning on the crankshaft .

Pete . :)
Logged
Goes around , Comes around . :)

Ricks

  • Administrator
  • Hero Member
  • *****
  • Posts: 3633
  • 1953 Automatic
    • View Profile
    • Email
Re: Flywheel torque
« Reply #2 on: April 09, 2023, 02:10:34 PM »
I don’t have a spec either, but I’ve never seen a broken key on a Simplex. What I have seen many times is a cracked keyway in the flywheel. A quick google search shows Cushman flywheel nuts get torqued to about 50-60 lb-ft.
Logged
Rick

pd

  • Hero Member
  • *****
  • Posts: 3130
    • View Profile
Re: Flywheel torque
« Reply #3 on: April 09, 2023, 03:08:04 PM »
Quote from: Ricks on April 09, 2023, 02:10:34 PM
I don’t have a spec either, but I’ve never seen a broken key on a Simplex. What I have seen many times is a cracked keyway in the flywheel. A quick google search shows Cushman flywheel nuts get torqued to about 50-60 lb-ft.

I should have taken pics of the few sheared keys that I had happen . I will say that I haven't had it happen since I welded the keyway . But , that wasn't all that long ago .

Pete . :)
Logged
Goes around , Comes around . :)

Ricks

  • Administrator
  • Hero Member
  • *****
  • Posts: 3633
  • 1953 Automatic
    • View Profile
    • Email
Re: Flywheel torque
« Reply #4 on: April 09, 2023, 06:36:55 PM »
Pete, did they shear when running or trying to start it? How sloppy was your keyway? How bad was the flywheel to crank fit. I think all mine would run without a key at all!
Logged
Rick

pd

  • Hero Member
  • *****
  • Posts: 3130
    • View Profile
Re: Flywheel torque
« Reply #5 on: April 10, 2023, 06:21:13 AM »
Quote from: Ricks on April 09, 2023, 06:36:55 PM
Pete, did they shear when running or trying to start it? How sloppy was your keyway? How bad was the flywheel to crank fit. I think all mine would run without a key at all!

Rick ,
All would shear very soon after starting . It would run for only a few RPMs and done .
The keyway was much like ramwing7s' :

And , the taper fit wasn't near as pitted as in that^ pic . It seemed fairly good , but I did notice a bit of surface rust on the crank taper after it had sat for a few months , flywheel mounted and untouched . So , I knew that the taper needed some lapping to be better .

Pete . :)
Logged
Goes around , Comes around . :)

Ricks

  • Administrator
  • Hero Member
  • *****
  • Posts: 3633
  • 1953 Automatic
    • View Profile
    • Email
Re: Flywheel torque
« Reply #6 on: April 10, 2023, 06:33:01 PM »
That keyway looks terrible. I would weld it up and remachine it.
Logged
Rick

pd

  • Hero Member
  • *****
  • Posts: 3130
    • View Profile
Re: Flywheel torque
« Reply #7 on: April 11, 2023, 05:39:07 AM »
Quote from: Ricks on April 10, 2023, 06:33:01 PM
That keyway looks terrible. I would weld it up and remachine it.

I did weld it and I hand filed it back to size .
Holds the key nicely . ;)

Pete . :)
Logged
Goes around , Comes around . :)
Pages: [1]   Go Up
« previous next »