« previous next »
Pages: 1 2 3 4 [5]   Go Down

Author Topic: Safti-Cycle Commando  (Read 4015 times)

pd

  • Hero Member
  • *****
  • Posts: 3130
    • View Profile
Re: Safti-Cycle Commando
« Reply #60 on: October 28, 2024, 09:19:16 AM »
You must be doing something right , Bruce . ;)

Pete . :)
Logged
Goes around , Comes around . :)

Carbineone1964

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #61 on: October 28, 2024, 04:25:26 PM »
Thanks

Rode it around again this eve for about 45 minutes..Kinda addicting to ride..Too bad Winter is coming soon..

I have the decal for the side cover on and the tank and the cover clear coated..Kick Start from Wayne is all done too...

Next thing is the foot boards..They should arrive this week..Will be nice to have those on..Once those are on, I can do the rear brake pedal and linkage..
Logged

Ricks

  • Administrator
  • Hero Member
  • *****
  • Posts: 3633
  • 1953 Automatic
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #62 on: October 29, 2024, 05:52:09 PM »
Make a stop so the kick start doesn’t flop so far forward.
Logged
Rick

Carbineone1964

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #63 on: October 29, 2024, 11:05:50 PM »
Yes that is in the plan. Otherwise it hits my little pinion cover..I just have not decided where to locate it quite yet...

I did get the ignition wired up today..Not alot I can do till the exhaust and the floor boards get here..I did ride it again today for around ten miles. Everything is still working well mechanically. Thanks
« Last Edit: October 29, 2024, 11:10:34 PM by Carbineone1964 »
Logged

Carbineone1964

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #64 on: November 01, 2024, 12:31:27 PM »
Put a tailpipe on today..It is ran through the forward original hole, then rearward..No I did not drill those two holes at the rear, they were there when I bought the frame..Not sure for what purpose.. The pipe is for stationary diesel generators.. So time will tell if it will hold up in a mobile environment..
Logged

Carbineone1964

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #65 on: November 02, 2024, 10:40:24 AM »
Rick

I put a rubber stopper under the kicker..It seems that will work good..Thanks
Logged

kartjockey

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1669
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #66 on: November 04, 2024, 08:36:26 AM »
Nice finish!  The Model Y Briggs cover was the touch!
Logged

Carbineone1964

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #67 on: November 04, 2024, 03:42:00 PM »
Yes that cover was a ingenious idea,LOL  Seriously it does just look right on there..

The Footboards did arrive today. Have them on..They should suffice. Finishing up the rear brake setup is next...

Not sure what to do on the clutches yet..Leave em open or fab a cover?  What do you think? Ideas?

Thanks for following along.
« Last Edit: November 04, 2024, 03:43:33 PM by Carbineone1964 »
Logged

Carbineone1964

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #68 on: November 05, 2024, 02:19:46 PM »
This is what I was doing today..Making the rear brake pedal.. I will show a pic when it is mounted up..Should be pretty Kool...Thanks
Logged

Carbineone1964

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #69 on: November 06, 2024, 04:02:19 PM »
Rear pedal and linkage is done..Going to work great I think..If some do not know what the pedal is from..It is a modified Kickstarter of a Old Briggs Washing Machine type motor..Thanks
Logged

pd

  • Hero Member
  • *****
  • Posts: 3130
    • View Profile
Re: Safti-Cycle Commando
« Reply #70 on: November 07, 2024, 06:48:05 AM »
That pedal looks like it belongs there .
Repurposed for another life of service . ;)

Pete . :)
Logged
Goes around , Comes around . :)

Carbineone1964

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #71 on: November 07, 2024, 10:07:45 AM »
Thanks

The sidecover came from the same motor.. I kinda hated to scavenge the Little kick start Briggs.. But it needed some work..I did not want to put the money into it..And selling those local is not that easy around here, and shipping them is a pain..
Logged

Carbineone1964

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #72 on: November 14, 2024, 01:30:38 PM »
Someone suggested I should put a cover on the drive pulley just for a little more Safti added into the Cycle..LOL



Anyway the aluminum plates I ordered arrived today and I have it all done..Looks kinda cool too..Have the tailight, battery and headlight all done too..I will show those pics later..Thanks
« Last Edit: November 14, 2024, 04:26:43 PM by Carbineone1964 »
Logged

Scooter4

  • Full Member
  • ***
  • Posts: 165
    • View Profile
Re: Safti-Cycle Commando
« Reply #73 on: November 17, 2024, 08:50:56 AM »
That is really cool.  I agree that the flywheel cover looks right at home.
Great Job.
Logged

Carbineone1964

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Safti-Cycle Commando
« Reply #74 on: November 17, 2024, 07:08:41 PM »
Thank You

Here is the headlight and taillight..I am pretty much done for now..



Logged
Pages: 1 2 3 4 [5]   Go Up
« previous next »